WatPass® pHGo for raising the pH value of your well water 5.0 m 3 /h
3.019,00 €
Tilgængelig, leveringstid: 1-3 Tage
Anlage WatPass® pHGo - zur Erhöhung des pH-Wertes Ihres Quellwassers. Die WatPass® pHGo wird auch häufig als Ergänzung zum WatPass® IronGo verwendet, wenn eine Enteisenung mit diesem Gerät, aufgrund von pH-Werten unter 6,8 nicht mehr möglich ist.
Produktinformation "WatPass® pHGo for raising the pH value of your well water 5.0 m 3 /h"
If, as a well operator, you have low pH levels in your water and you want to use it as drinking water, the WatPass® pHGo offers you an excellent opportunity to increase the ph value in order to comply with the regulations of the Drinking Water Ordinance (pH 6.5-9, 5, TrinkwVo 2001/11). The system consists of a GRP pressure bottle, which is filled with a material for pH increase. A volume-controlled central control valve, type Clack WS 1 CI, currently represents the ultimate in control valves for such systems.
Background
Acidic water is corrosive. As the pH drops, the proportion of free carbonic acid increases, attacking all metals except stainless steel. This leads to leaks in the water installation over time. It also pollutes your drinking water with copper, zinc or aluminum. The WatPass pHGo contains a mineral that neutralizes the excess carbonic acid and immediately increases the pH value. The mineral is a consumable and must be refilled 1-3 times a year, depending on local conditions.
Installation
Behind the well pump or in front of the pressure vessel, if available. To ensure proper backwash, a pressure control must be installed in front of the neutralizer or a bypass of the existing pressure switch to allow the well pump to start delivering water when the neutralizer backwash valve is opened.
Recommendation: To maintain the performance and service life of the device, a sediment filter should be installed.
If the iron and manganese contents of your well water are too high and you want to use the WatPass IronGo, but the pH value is too low for the proper functioning of the device, then the WatPass phGo is the solution for this case! The WatPass phGo raises the pH of your well water to a level that allows the WatPass IronGo to be used for iron removal, even if the pH of your water is below 6.8.
The installation is serial, before the WatPass IronGo and is very simple. Depending on the desired performance or the amount of well water to be treated, the WatPass phGo is also available in other versions. If the model offered by us does not fit, of course we can also sell you another, suitable device. Just ask us!
Applications
Well water, garden irrigation, laundries, hot water, koi and fish ponds and all areas where too low ph value of your water prevents iron ironing with the IronGo.
Depending on the spatial conditions and equipment requirements, we recommend that you consider the purchase of the following accessories:
Connection set 1 inch depending on system size
2x armored hose 1 inch ÜM x 1 inch ÜM, L = 1.000 mm; 1x drain hose, L = 2,000mm;
1x hose clamp 1/2 inch; 4x seals; 1x overflow hose, L = 2.000mm
Connection set 1 1/4 inch depending on system size
2x armored hose 1 1/4 inch ÜM x 1 1/4 inch ÜM, L = 1.000 mm; 1x drain hose,
L = 2,000mm; 1x hose clamp 1/2 inch; 1x overflow hose; L = 2.000mm; 4x seals
Mounting block 1 inch IG x 1 inch AG
with intersection, bypass function, sampling tap
Note: A water analysis and determination of what the water should be used for is a prerequisite for good advice and the selection of the right filter system. Well water may be subject to variations in composition due to various environmental influences. Therefore, a regular analysis should take place to be able to adapt the filter devices by For example, the regeneration cycle is changed.
Installation instructions for connection to public networks: If the WP ManganGo filter systems are to be used in the drinking water sector, they must comply with the "Rules for drinking water installations" according to DIN 1988 -200 in conjunction with DIN EN 1717: 2011-08. Then it is necessary to install a backflow preventer to protect the public drinking water network. Necessary installation conditions: Water connection socket 230 V / 50 Hz, waste water connection, pressure reducer at> 6 bar
Transport and costs: The item is delivered to avoid transport damage by freight carrier.
Maximum power: 3.5m³ / h
Backwash flow: at least 3.0 m³ / h
Diameter: 335 mm
Height: 1398 mm
Ladenkiste UG (haftungsbeschränkt)
Bahnhofstr.
34286
Spangenberg
Deutschland
kontakt@wasserfilter-zentrum.de
Similar items
The WatPass® IronGo deferrisation system oxidises dissolved iron from your water. The Clack control head with German menu and colour display distinguishes this system from many other suppliers, as usually only monochrome, English-language versions are offered. The colour modes of the display make it easier to check the operating status (blue = everything is OK). If there is an error (red = fault), you can see this at a glance. The German menu makes setting the system much easier. Nothing needs to be changed or topped up. The IronGo is therefore virtually maintenance-free. Its performance is outstanding, it can filter up to 5 mg/l of iron from the water. Installation is very simple. Even during the backwash, water can be easily removed. At a freely programmable time (approximately every 7 days), the concentrate is automatically disposed of through an outlet. A 3 metre drain hose is supplied and can be replaced with a longer garden hose if necessary. An additional mounting block (accessory) can be purchased for bridging, but is not absolutely necessary for operation, although it is highly recommended. This helps to maintain the water supply with untreated water during maintenance work. The system consists of: GRP pressure bottle in various sizes (adapted to the capacity), which is filled with high-quality filter material. The catalyser granulate is coated with manganese dioxide (MnO2). Volume-controlled central control valve type Clack WS 1 CI IA. How the catalyst granulate works Iron is usually present as bicarbonate in groundwater. Due to the excess carbonic acid, iron cannot be filtered. As a catalyser, the filter material causes the transition from soluble Fe2+ to insoluble Fe3+, the resulting oxidation product iron hydroxide is easily filterable. A pH value of at least 6.8 (preferably 7.0) is required to filter iron successfully, regardless of the filter material used. If the pH value of your water is too low, please contact us specifically. This must then be raised by additional filter technology as a first step. We then recommend the WatPass pHGO system. Necessary installation conditions: Water connection socket 230 V / 50 Hz, waste water connection, pressure reducer at > 6 bar Product Details Flexible, space-saving design Corrosion-resistant GRP pressure bottle High-quality filter material Computer-controlled Clack WS 1 CI IAValve Volume Control Extremely low maintenance Treatment of ferrous water Reduction of the orange-brown colour tone in the water Areas of application: Well water, garden irrigation, laundries, industrial water utilisation, koi and fish ponds and all areas where excessive iron content in the water causes problems The WatPass IronGo is available in different versions depending on the required performance or the amount of well water to be treated (the colour of the pressure bottle may differ in some versions). You can find these in the selection menu. Note: If the IronGo filter systems are to be used in the drinking water sector, they must comply with the ‘Rules for drinking water installations’ in accordance with DIN 1988 -200 in conjunction with DIN EN 1717:2011-08. It is then necessary to install a pipe separator to protect the public drinking water network.
The connection set is suitable for the disinfestation systems AquaAvanti IronGo (except EV-B1 and EW-B1) and equipment for manganese removal such as AquaAvanti ManganGo (except models with 3,3m³/h and 4,4m³/h flowrate) or just as it is needed. Delivery The connection set 1 inch contains: 2x armored hose DVGW 1 "ÜMxÜM, L-1.000mm, drain hose and overflow hose each 1.500mm, 1/2" hose clamp, 4 gaskets
The assembly block is suitable for the AquaAvanti IronGo iron filter and manganese filter AquaAvanti ManganGo or where a bypass is needed. If there is limited space at the point of connection, the use of a mounting block is ideal. For safety reasons, it may be desirable to be able to bridge the device unit. For such cases, the mounting block (bypass) is ideal. The installation of a mounting block usually takes about one hour. Your installer will surely make you an offer. If you are not sure if you need a mounting block just ask him. The mounting block is working that way Position 1 When the two outer taps are closed and the middle tap is open, the water flows past the connected device (eg AquaAvanti Iron GO or AquaAvanti ManganGo). Position 2 If the two outer cocks are open and the middle closed, all the water flows through the connected devices. Note: If it is necessary to bridge the units, simply return the mounting block to position 1.