Reverse Osmosis Systems by WatPass^® for Residential and Commercial Use and AquaAvanti Osmo

The replacement filter unit for the WatPass reverse osmosis system EASY must be replaced every 12 months. The filter and membrane can be changed in no time and without tools thanks to the innovative single-cartridge system. All five filter levels can be changed in less than 30 seconds. The WatPass replacement filter cartridge EASY produces at least 1.5 liters per minute of the purest filtered drinking water from your drinking water - free of heavy metals, pesticides, drug residues, bacteria and viruses and with a soft taste. High quality membrane through nanotechnology The heart of an osmosis system is the elaborate filter technology and here in particular the membrane that works on the principle of reverse osmosis. Tap water is pressed into the osmosis system by high line pressure, where it is only freed from all larger particles, sediments and pollutants through pre-filters (PP cotton layers and activated carbon). The water is then pressed through a membrane, the holes of which are extremely small and therefore hardly any substances except pure water can pass through. The retained substances in front of the membrane are flushed out as waste water. The membrane of the WatPass was constructed in a perfect way through nanotechnology. Five-stage filter system of the WatPass reverse osmosis system EASY 1. The first PP cotton layer filters out sediments, rust and suspended matter 2. Activated carbon filters chlorine, organic compounds, taste and smell 3. Second layer of PP cotton removes further mechanical critical particles 4. Reverse osmosis membrane of 0.0001 µm filters heavy metals and organic substances such as pesticide residues, drug residues and much more 5. Activated carbon after-filter to optimize the taste Filter change EASY - and that in under 30 seconds! Conventional reverse osmosis systems do not always make changing the filter easy, because they usually contain several filter cartridges that can be more or less easily exchanged. The WatPass reverse osmosis system EASY impresses with its single cartridge system - the five-stage filter system is in one housing. Thanks to this innovative plug-in system, changing the filter is done in a very short time and you don't even have to interrupt the water supply. The reason for this is that the water supply is automatically interrupted by the system when the filter cartridge is changed. Therefore you do not have to think about turning off the water supply yourself beforehand. After water treatment by the WatPass EASY, the water is so pure and clear that you can drink it naturally and it is also very suitable for making baby food. Relieving your body of harmful substances certainly makes sense, treat yourself and your health to something good. In the household, the filtered water is also ideal for your ironing water and for cleaning glass surfaces. Limescale stains are history and you will never have problems with calcified kettles, fittings, windows or irons again.

Digital, mobile and shapely conductivity meter for hand measurements (measuring range: 0 - 1999 ppm) The digital, mobile and stylish conductivity meter for handheld measurements, with a measuring range of 0 - 1999 ppm. If you want to know the conductance value in µS or mg/l, this can be easily converted. The following conversion key applies: 1.2 µS/cm = 1 ppm = 1 mg/l. The measured values are easy to read on the digital display. The conductivity meter has two electrical conductivity probes that are resistant to salt deposits. It is particularly energy-saving, thanks to an automatic switch-off function that switches the device into power-save mode after 12 seconds. What is conductivity? It is the ability of a material to conduct electricity. The conductivity value is the total sum of the concentration of ions (anions and cations) in a solution that conduct electricity. It therefore provides information about the ionic strength of a solution, but not about the type of ions. Areas of use and application of the conductivity meter Conductivity is an important measurand for many areas, including drinking water and waste water, industrial manufacturing processes, aquarium water and also quality control in the food industry. Examples of conductivity in aqueous media* -Pure water: 0.055 μS/cm -Distilled water: 0.5 μS/cm -Mountain water: 1.0 μS/cm -Rainwater: 50 μS/cm -Drinking water: 300 - 800μS/cm -Drinking water (max. conductance): 1055μS/cm -Industrial wastewater: 5mS/cm -sea water: 52 mS/cm *(at 25°C)

The WatPass reverse osmosis system EASY is a noble, very compact osmosis system with which you can produce the purest water quality for your home in seconds. The water treatment system impresses with its small housing and at the same time very high-quality design. It is perfect for your household and impresses above all with its innovative, easy operation. The WatPass reverse osmosis system EASY produces at least 1.5 liters per minute of the purest filtered drinking water from your drinking water - free of impurities and smooth in taste. The filter water/waste water ratio of 1:1 makes it extremely economical, as this is an outstanding value in the field of reverse osmosis systems. Since the system is connected directly to the drinking water line (direct flow system), you can enjoy fresh, clear and pure water in no time at all. The risk of contamination from a connected tank is completely eliminated with our product, the WatPass reverse osmosis system EASY. WatPass reverse osmosis system with an innovative filter system in one unit The five stages of the filter system are combined in one functional unit. As a result, changing the filter at all filter levels is child's play and takes less than 30 seconds! High quality membrane through nanotechnology The heart of an osmosis system is the elaborate filter technology and here in particular the membrane that works on the principle of reverse osmosis. Tap water is pressed into the osmosis system by high line pressure, where it is only freed from all larger particles, sediments and pollutants through pre-filters (PP cotton layers and activated carbon). The water is then pressed through a membrane, the holes of which are extremely small and therefore allow almost no substances to pass through, apart from pure water. The retained substances in front of the membrane are flushed out as waste water. The membrane of the WatPass was constructed in a perfect way through nanotechnology. Five-stage filter system of the WatPass reverse osmosis system EASY 1. The first PP cotton layer filters out sediments, rust and suspended matter 2. Activated carbon filters chlorine, organic compounds, taste and smell 3. Second layer of PP cotton removes further mechanical critical particles 4. Reverse osmosis membrane of 0.0001 µm filters heavy metals and organic substances such as pesticide residues, drug residues and much more 5. Activated carbon post-filter for taste optimization Filter change EASY - and that in under 30 seconds! Conventional reverse osmosis systems do not always make changing the filter easy, because they usually contain several filter cartridges that can be more or less easily exchanged. The WatPass reverse osmosis system EASY impresses with its single cartridge system - the five-stage filter system is in one housing. Thanks to this innovative plug-in system, the filter change is done in a very short time and you don't even have to interrupt the water supply. The reason for this is that the water supply is automatically interrupted by the system when the filter cartridge is changed. Therefore you do not have to think about turning off the water supply yourself beforehand. Modern design in a compact size Thanks to the very small dimensions of the WatPass reverse osmosis system EASY, it can be easily installed almost anywhere. It can be easily installed without any special technical knowledge. The operating instructions with easy-to-understand illustrations - are clear, concise and describe every step that is required. The WatPass reverse osmosis system EASY is designed in elegant black and gray and you neither see a filter cartridge nor can it be seen that it could be an osmosis system. The magnetic front panel is also practical and looks chic. It's a shame that the system usually disappears under the sink. Use After the water treatment by the WatPass EASY, the water is so pure and clear that you can drink it naturally and it is also very suitable for the production of baby food. Relieving your body of harmful substances certainly makes sense, treat yourself and your health to something good. In the household, the filtered water is also ideal for ironing water and for cleaning glass surfaces. Limescale stains are history and you will never have problems with calcified kettles, faucets, windows or irons again.

AquaAvanti Osmo Reverse Osmosis Water Filter System designed and assembled in GermanyExcellent water for your well-being :-)We need about three liters of drinking water per person per day. Many households drink bottled water, because they do not like the taste of tap water. This is an expensive, inconvenient and ecologically questionable solution. However, almost every household has tap water, which is ideal as a raw material for further processing. The AquaAvanti Osmo Reverse Osmosis System will provide you with the daily amount of very clean and tasting water you need from your regular tap water network, saving you a lot of money and protecting the environment within a year.In addition, you will get your "Airbag in the kitchen" with the AquaAvanti Osmo RO System. No matter what harmful or dangerous substances come out of your water pipes, your AquaAvanti Osmo reduces almost all substances contained in the water over several filtration stages to a level where they are no longer bothersome and the water is absolutely harmless to drink.The process of reverse osmosis has been proven for decades and is even used to desalinate seawater. With its patented and hydraulically driven permeation pump, the AquaAvanti Osmo device saves a lot of water compared to conventional reverse osmosis units and at the same time consumes no electricity.Use for everyday enjoyment and ideal for:      Prepare food and drinks     For the production of unspoiled baby food     Relief of dialysis patients     To protect your high quality home appliances such as kettles, coffee makers, espresso machines, etc.     For skin and facial care     No visible water marks on cleaned surfaces like glass, mirrors etc. What characterizes the AA Osmo reverse osmosis system?      Production of the purest, highest quality, light (demineralized) and fresh drinking water through three filters, a membrane and the patented permeate pump     Daily production up to 85l (tank volume 12 liters)     Better and fresher taste of the water by incorporation of a special ceramic in the filter     Only high quality components, developed and assembled in Germany Filter tap water with Aqua Avanti OsmoIts tap water passes through the pre-filter stages and the hydraulic shut-off valve into the reverse osmosis module. The purified water penetrates the membrane.From the membrane, the purified water flows into the pumping chamber of the permeate pump. The system's waste water drives the pump, which delivers the purified water to the pressure tank. The permeate pump is a patented invention that improves the performance and efficiency of the plant. The pure water is ready for removal in the pressure tank.A hydraulic shut-off valve controls the water supply of the system. If you open the faucet of the system, the water flows through the post filter before you can enjoy it fresh. The system works without electricity only with the energy of the water pressure.Flow chart Aqua Avanti Osmo Tap water may have a maximum of 2000 microsiemens. This corresponds to 1280 mg / l of dissolved substances. Reverse Osmosis works like a very fine sieve. This "sieve" filters ions in the molecular range. It also makes the control of effectiveness so easy. Since even single atoms such as dissolved heavy metals or small ions such as sodium and nitrate are reduced, the pure water of the "Aqua Avanti Osmo" reverse osmosis system has a very low conductivity. The conductivity of the water is below 80 microsiemens when the "Aqua Avanti Osmo" produces water in high purity.Advantages of the patented permeate pump      Clean and pure water at home every time     Save money!      Your "airbag" for the kitchen     Never carry heavy water boxes     Development and installation of the device in Germany with competent support!     Version with sediment pre-filter and activated carbon pre-filter to protect the high-quality reverse osmosis membrane.     Activated carbon post-filter for best taste     No loss of efficiency compared to systems without permeate pump     Faster production of water     No electrical connection necessary     No power consumption     The hydraulic energy of the water is used to separate the wastewater (concentrate) and to transport the filter water (permeate) into the storage tank     ratio 1: 3 (permeate to concentrate); for cheap equipment up to 1:15     Made in Germany Membrane and filter     Easy change of filters (every 6-12 months) and the membrane (up to 36 months) with bayonet lock. There is no tool necessary!    Color coding of the filters and membranes prevents confusion during filter replacement.    red = pre-filter  yellow = activated carbon pre-filter  green = reverse osmosis module (membrane)  blue = activated carbon secondary filterInstallation    little need for space Environmental conditions       Inlet water temperature 2-36 ° degrees Celsius      The system should be operated with a pressure of at least 3 -6 bar. At less pressure, the filter performance decreases sharply, the quality suffers and you get hardly any water in the tank. If the line pressure is often below 3 bar, we recommend devices with booster pump. The very energy-saving pumps now have a good life and supply the reverse osmosis membrane with 7 bar pressure.Scope of delivery: Reverse osmosis system with membrane, filter cartridges, stainless steel tank and stainless steel design faucet - mounting accessoriesWeight: approx. 10.25kg incl. PackagingSize of the packaging: 48x18x32cm

On-mineralization as an extension filter stage of the Aqua Avanti Inline series with quick-change housings and original CARBONIT filters. This extension filter stage can be used in conjunction with a main filter stage. The extension stage consists of a filter cartridge and the filter head, but a shorter connecting hose for connection to the main filter stage. Description of the Aqua Avanti Inline system Forget about dismantling and unscrewing filter housings to change filters. With the AA Inline filter system, you can change filter cartridges in seconds. Simply remove the filter cartridge by turning it counterclockwise and insert a new filter cartridge the other way around. Done. You no longer need a housing key. Since you do not come into contact with the inside of the filter cartridge, the replacement is very hygienic. Description of the Calci Mineralization Inline filter The mineralization cartridge is filled with calcium granules, which are extracted off the coast of Okinawa under controlled and absolutely environmentally friendly conditions. Fossil corals are also used to produce nutritional supplements in the form of powder, e.g. for enriching muesli, or calcium tablets. For this cartridge a granulate is used, which has the optimal size and composition for drinking water remineralization. The Calci EM additionally contains EM Pipes. Areas of application: Suitable for anyone who wants to enhance their drinking water with high quality coral calcium. Especially suitable to post-treat the water behind reverse osmosis systems, so that it tastes better. Or as a second or third stage for the AquaAvanti Inline water filter series. Usage: The remineralization cartridge has to be changed after approx. one year, depending on the usage. Use only with cold water, protect from frost. Weight approx. 800 gr.

 LG BW 4040 ES brackish water membrane for WatPass RO 6500 - 36000 reverse osmosis systems The NanoH2O™ brackish water RO membranes from world market leader LG Chem are used for various municipal and industrial applications. They are used in large companies all over the world. With innovative thin-film nanocomposite (TFN) technology, all LG BW reverse osmosis membranes offer outstanding performance and have integrated anti-fouling properties. Suitable for all applications where consistent and reliable performance is required. Field of application The LG BW 4040 ES membranes offer high permeability at a very low inlet pressure. This significantly reduces operating costs. They are suitable for brackish water applications with low to medium salinity. Design The optimum membrane module can be determined using the Q+ design software. Just ask us if you need assistance. Variants We offer the following membrane modules with different properties: LG BW R G2 Outstanding rejection, high flow rate, long service life LG BW ES Energy saving LG BW UES Ultra-low energy

WatPass® RO6500 reverse osmosis system (250l/h) Industrial reverse osmosis systems are used where industrial waste water from car washes, medical facilities, laboratories and other facilities is to be purified on site. WatPass® reverse osmosis systems are available in various sizes and designs to optimally match the volume of water to be purified. How does a reverse osmosis system work? The operating principle of an osmosis system is that two solutions with different particle concentrations that are separated by a semi-permeable membrane generate osmotic pressure. This happens because both solutions endeavour to equalise their particle concentration. In nature, this osmosis principle is vital within cells, as this is the only way to equalise the internal cell pressure and regulate the water balance within each cell. In the reverse osmosis system, the principle is practically reversed by increasing the pressure on one of the liquids. This forces the water in the reverse osmosis system through the multi-layer reverse osmosis membrane. This contains many small pores and is therefore also known as a semi-permeable membrane. As a result, almost all undesirable components such as limescale, pollutants, germs and other impurities are filtered out of the water. The result is pure water (permeate) of drinking water quality. Commercial reverse osmosis systems are reliable, turnkey solutions for various commercial and residential applications. Water bottling plants, steam boilers, garden centres, restaurants and many other types of businesses benefit from their excellent performance and durability. Benefits & Features of the WatPass® RO6500 Reverse Osmosis System AQ 5000 control unit -Easy operation thanks to intelligent architecture Universal system design enables connection options for permeate flushing and raw water blending Worldwide Grundfos guarantee CE marking and confirmation of safety in accordance with the EC New Approach Directives  Technical components Grundfos pump CM 1-10 300 psi diaphragm tank BB10 sediment pre-filter Electrical control panel with control unit Danfoss solenoid valves Piping, instrumentation steel frame Wooden crate for transport Options Dosing pump for antiscalant / antiscalant for various applications Versatile set for raw water mixing (30...240 l/h) or permeate rinsing Specifications Permeate capacity* - 250 L/h Permeate recovery** - 75% Maximum TDS - 3000 mg/L Inlet flow requirement: 320...400 L/h (operation) | 1500...2000 L/h (flushing) Operating pressure: 8...12 bar Maximum pressure: 14 bar Electrical requirements: 230 V, 50 Hz (1 ph) Electrical power: 0.7 kW pre-filter capacity: 5 μm* *depending on the TDS value of the feed water, the temperature and the permeate recovery ** for low limescale/contaminated water Requirements for the feed water Temperature of the incoming water: +5...+40 °С Maximum residual chlorine: 0.1 mg/L Hardness: up to 3 meq/L (150 mg/L CaCO₃) Iron: up to 0.1 mg/L Manganese: up to 0.05 mg/L Silicate: up to 20 mg/L Chemical oxygen demand, max: 4.0 mg О₂/L Hydrogen sulphide: none The limit values may be exceeded if an antiscalant, oxygen absorber or other chemical pre-treatment is used for reverse osmosis. AQ-5000 controller The AQ-5000 controller is designed for automatic or manual control of the reverse osmosis system and offers: automatic switching on and off of the unit on signal Emergency shutdown of the system by signals from: Dry-running sensors, overpressure in the module deactivation of the devices by the external STOP signal Hydraulic flushing of the membranes continuous quality control (electrical conductivity and temperature) of the permeate  

WatPass® RO12000 reverse osmosis system (500l/h) Industrial reverse osmosis systems are used where industrial waste water from car washes, medical facilities, laboratories and other facilities is to be purified on site. WatPass® reverse osmosis systems are available in various sizes and designs to optimally match the volume of water to be purified. How does a reverse osmosis system work? The operating principle of an osmosis system is that two solutions with different particle concentrations that are separated by a semi-permeable membrane generate osmotic pressure. This happens because both solutions endeavour to equalise their particle concentration. In nature, this osmosis principle is vital within cells, as this is the only way to equalise the internal cell pressure and regulate the water balance within each cell. In the reverse osmosis system, the principle is practically reversed by increasing the pressure on one of the liquids. This forces the water in the reverse osmosis system through the multi-layer reverse osmosis membrane. This contains many small pores and is therefore also known as a semi-permeable membrane. As a result, almost all undesirable components such as limescale, pollutants, germs and other impurities are filtered out of the water. The result is pure water (permeate) of drinking water quality. Commercial reverse osmosis systems are reliable, turnkey solutions for various commercial and residential applications. Water bottling plants, steam boilers, garden centres, restaurants and many other types of businesses benefit from their excellent performance and durability. Benefits & Features of the WatPass® RO12000 Reverse Osmosis System AQ 5000 control unit -Easy operation thanks to intelligent architecture Universal system design enables connection options for permeate flushing and raw water blending Worldwide Grundfos guarantee CE marking and confirmation of safety in accordance with the EC New Approach Directives  Technical components Grundfos pump CM 1-10 300 psi diaphragm tank BB10 sediment pre-filter Electrical control panel with control unit Danfoss solenoid valves Piping, instrumentation steel frame Wooden crate for transport Options Dosing pump for antiscalant / antiscalant for various applications Versatile set for raw water mixing (30...240 l/h) or permeate rinsing Specifications Permeate capacity* - 500 L/h Permeate recovery** - 75% Maximum TDS - 3000 mg/L Inlet flow requirement: 650...800 L/h (operation) | 1500...2000 L/h (flushing) Operating pressure: 8...12 bar Maximum pressure: 14 bar Electrical requirements: 230 V, 50 Hz (1 ph) Electrical power: 0.7 kW pre-filter capacity: 5 μm* *depending on the TDS value of the feed water, the temperature and the permeate recovery ** for low limescale/contaminated water Requirements for the feed water Temperature of the incoming water: +5...+40 °С Maximum residual chlorine: 0.1 mg/L Hardness: up to 3 meq/L (150 mg/L CaCO₃) Iron: up to 0.1 mg/L Manganese: up to 0.05 mg/L Silicate: up to 20 mg/L Chemical oxygen demand, max: 4.0 mg О₂/L Hydrogen sulphide: none The limit values may be exceeded if an antiscalant, oxygen absorber or other chemical pre-treatment is used for reverse osmosis. AQ-5000 controller The AQ-5000 controller is designed for automatic or manual control of the reverse osmosis system and offers: automatic switching on and off of the unit on signal Emergency shutdown of the system by signals from: Dry-running sensors, overpressure in the module deactivation of the devices by the external STOP signal Hydraulic flushing of the membranes continuous quality control (electrical conductivity and temperature) of the permeate  

WatPass® RO24000 reverse osmosis system (1000l/h) Industrial reverse osmosis systems are used where industrial waste water from car washes, medical facilities, laboratories and other facilities is to be purified on site. WatPass® reverse osmosis systems are available in various sizes and designs to optimally match the volume of water to be purified. How does a reverse osmosis system work? The operating principle of an osmosis system is that two solutions with different particle concentrations that are separated by a semi-permeable membrane generate osmotic pressure. This happens because both solutions endeavour to equalise their particle concentration. In nature, this osmosis principle is vital within cells, as this is the only way to equalise the internal cell pressure and regulate the water balance within each cell. In the reverse osmosis system, the principle is practically reversed by increasing the pressure on one of the liquids. This forces the water in the reverse osmosis system through the multi-layer reverse osmosis membrane. This contains many small pores and is therefore also known as a semi-permeable membrane. As a result, almost all undesirable components such as limescale, pollutants, germs and other impurities are filtered out of the water. The result is pure water (permeate) of drinking water quality. Commercial reverse osmosis systems are reliable, turnkey solutions for various commercial and residential applications. Water bottling plants, steam boilers, garden centres, restaurants and many other types of businesses benefit from their excellent performance and durability. Benefits & Features of the WatPass® RO24000 Reverse Osmosis System AQ 5000 control unit -Easy operation thanks to intelligent architecture Universal system design enables connection options for permeate flushing and raw water blending Worldwide Grundfos guarantee CE marking and confirmation of safety in accordance with the EC New Approach Directives  Technical components Grundfos pump CM 1-10 300 psi diaphragm tank BB10 sediment pre-filter Electrical control panel with control unit Danfoss solenoid valves Piping, instrumentation steel frame Wooden crate for transport Options Dosing pump for antiscalant / antiscalant for various applications Versatile set for raw water mixing (30...240 l/h) or permeate rinsing Specifications Permeate capacity* - 1000 L/h Permeate recovery** - 75% Maximum TDS - 3000 mg/L Inlet flow requirement: 1300...1500 L/h (operation) | 3000...4000 L/h (flushing) Operating pressure: 8...12 bar Maximum pressure: 14 bar Electrical requirements: 230 V, 50 Hz (1 ph) Electrical power: 2,0 kW pre-filter capacity: 5 μm* *depending on the TDS value of the feed water, the temperature and the permeate recovery ** for low limescale/contaminated water Requirements for the feed water Temperature of the incoming water: +5...+40 °С Maximum residual chlorine: 0.1 mg/L Hardness: up to 3 meq/L (150 mg/L CaCO₃) Iron: up to 0.1 mg/L Manganese: up to 0.05 mg/L Silicate: up to 20 mg/L Chemical oxygen demand, max: 4.0 mg О₂/L Hydrogen sulphide: none The limit values may be exceeded if an antiscalant, oxygen absorber or other chemical pre-treatment is used for reverse osmosis. AQ-5000 controller The AQ-5000 controller is designed for automatic or manual control of the reverse osmosis system and offers: automatic switching on and off of the unit on signal Emergency shutdown of the system by signals from: Dry-running sensors, overpressure in the module deactivation of the devices by the external STOP signal Hydraulic flushing of the membranes continuous quality control (electrical conductivity and temperature) of the permeate  

WatPass® RO24000 reverse osmosis system (1500l/h) Industrial reverse osmosis systems are used where industrial waste water from car washes, medical facilities, laboratories and other facilities is to be purified on site. WatPass® reverse osmosis systems are available in various sizes and designs to optimally match the volume of water to be purified. How does a reverse osmosis system work? The operating principle of an osmosis system is that two solutions with different particle concentrations that are separated by a semi-permeable membrane generate osmotic pressure. This happens because both solutions endeavour to equalise their particle concentration. In nature, this osmosis principle is vital within cells, as this is the only way to equalise the internal cell pressure and regulate the water balance within each cell. In the reverse osmosis system, the principle is practically reversed by increasing the pressure on one of the liquids. This forces the water in the reverse osmosis system through the multi-layer reverse osmosis membrane. This contains many small pores and is therefore also known as a semi-permeable membrane. As a result, almost all undesirable components such as limescale, pollutants, germs and other impurities are filtered out of the water. The result is pure water (permeate) of drinking water quality. Commercial reverse osmosis systems are reliable, turnkey solutions for various commercial and residential applications. Water bottling plants, steam boilers, garden centres, restaurants and many other types of businesses benefit from their excellent performance and durability. Benefits & Features of the WatPass® RO24000 Reverse Osmosis System AQ 5000 control unit -Easy operation thanks to intelligent architecture Universal system design enables connection options for permeate flushing and raw water blending Worldwide Grundfos guarantee CE marking and confirmation of safety in accordance with the EC New Approach Directives  Technical components Grundfos pump CM 1-10 300 psi diaphragm tank BB10 sediment pre-filter Electrical control panel with control unit Danfoss solenoid valves Piping, instrumentation steel frame Wooden crate for transport Options Dosing pump for antiscalant / antiscalant for various applications Versatile set for raw water mixing (30...240 l/h) or permeate rinsing Specifications Permeate capacity* - 1500 L/h Permeate recovery** - 75% Maximum TDS - 3000 mg/L Inlet flow requirement: 2000...2500 L/h (operation) | 3000...4000 L/h (flushing) Operating pressure: 8...12 bar Maximum pressure: 14 bar Electrical requirements: 230 V, 50 Hz (1 ph) Electrical power: 2,0 kW pre-filter capacity: 5 μm* *depending on the TDS value of the feed water, the temperature and the permeate recovery ** for low limescale/contaminated water Requirements for the feed water Temperature of the incoming water: +5...+40 °С Maximum residual chlorine: 0.1 mg/L Hardness: up to 3 meq/L (150 mg/L CaCO₃) Iron: up to 0.1 mg/L Manganese: up to 0.05 mg/L Silicate: up to 20 mg/L Chemical oxygen demand, max: 4.0 mg О₂/L Hydrogen sulphide: none The limit values may be exceeded if an antiscalant, oxygen absorber or other chemical pre-treatment is used for reverse osmosis. AQ-5000 controller The AQ-5000 controller is designed for automatic or manual control of the reverse osmosis system and offers: automatic switching on and off of the unit on signal Emergency shutdown of the system by signals from: Dry-running sensors, overpressure in the module deactivation of the devices by the external STOP signal Hydraulic flushing of the membranes continuous quality control (electrical conductivity and temperature) of the permeate  

 LG BW 4040 ES brackish water membrane for WatPass RO 6500 - 36000 reverse osmosis systems The NanoH2O™ brackish water RO membranes from world market leader LG Chem are used for various municipal and industrial applications. They are used in large companies all over the world. With innovative thin-film nanocomposite (TFN) technology, all LG BW reverse osmosis membranes offer outstanding performance and have integrated anti-fouling properties. Suitable for all applications where consistent and reliable performance is required. Field of application The LG BW 4040 ES membranes offer high permeability at a very low inlet pressure. This significantly reduces operating costs. They are suitable for brackish water applications with low to medium salinity. Design The optimum membrane module can be determined using the Q+ design software. Just ask us if you need assistance. Variants We offer the following membrane modules with different properties: LG BW R Outstanding rejection, high flow rate, long service life LG BW ES Energy saving LG BW UES Ultra-low energy

 LG BW 4040 R brackish water membrane for WatPass RO 6500 - 36000 reverse osmosis Systems The NanoH2O™ brackish water RO membranes from world market leader LG Chem are used for various municipal and industrial applications. They are used in large companies all over the world. With innovative thin-film nanocomposite (TFN) technology, all LG BW reverse osmosis membranes offer outstanding performance and have integrated anti-fouling properties. Suitable for all applications where consistent and reliable performance is required. Field of application LG BW R membranes offer a combination of high retention and reliability. It is suitable for brackish water with high salinity and wastewater reuse. This means they are ideal for applications where consistent and reliable performance is required. Sizing The optimum membrane module can be determined using the Q+ design software. Just ask us if you need assistance. Variants We offer the following membrane modules with different properties: LG BW R G2 Outstanding rejection, high flow rate, long service life LG BW ES Energy saving LG BW UES Ultra-low energy