Stainless Steel UV Household Water Filtration System - Germ-Free Water for Small Water Quantities, Well Filtration, Ponds & Pools

The UV-C water treatment systems of the Pure series, like all UV systems, require a regular change of the lamps in order to guarantee the disinfection performance during operation. Change intervals     UV-C 21 watts: approx. 8000 hours     UV-C 40 watts: approx. 8000 hours     UV-C 50 watt: approx. 8000 hours     UV-C 75 watt: approx. 8000 hours     UV-C amalgam 120 watts: approx. 10,000 hours What is UV water treatment? Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! Treatment at a wavelength of 254 nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. With UV irradiation, germs can be safely used in water without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what has been treated with chlorine. Maintenance Replacement of the UV lamps approximately every 12 months The lamps can be easily loosened with screws and then pulled out for replacement.

The UV water treatment system Pure 1.2 21W from the manufacturer UST is used to inactivate germs such as bacteria and viruses. It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment?Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical informationDue to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of 1080 l/h is achieved with a extremely low power consumption of 21 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! MaintenanceExchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: 1" inch * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary

The UV water treatment system Pure 1.0 16W S from the manufacturer UST is used to inactivate germs such as bacteria and viruses. It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment? Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical information Due to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of 330 l/h is achieved with a extremely low power consumption of 16 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! Maintenance Exchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: 1/2" inch * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary

The UV water treatment system Pure 2.1 50W from the manufacturer UST is used to inactivate germs such as bacteria and viruses. It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment?Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical informationDue to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of  2400 l/h is achieved with a very low power consumption of 50 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! MaintenanceExchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: Standard 2 "inch or alternatively 1" inch possible (if 1 "inch desired, please specify when ordering). * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary

The UV water treatment system Pure 2.4 from the manufacturer UST is used to inactivate germs such as bacteria and viruses. It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment?Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical informationDue to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of 3100 l/h is achieved with a very low power consumption of 75 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! MaintenanceExchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: Standard 2 "inch or alternatively 1" inch possible (if 1 "inch desired, please specify when ordering). * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary

The UV water treatment system Pure 2.4 40W from the manufacturer UST is used to inactivate germs such as bacteria and viruses. It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment?Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical informationDue to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of 2300 l/h is achieved with a very low power consumption of 40 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! MaintenanceExchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: Standard 2 "inch or alternatively 1" inch possible (if 1 "inch desired, please specify when ordering). * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary

The energy-saving UV water treatment unit Pure SE 1.2 50 W from the manufacturer UST is used to inactivate germs such as bacteria and viruses. It is completely manufactured in Germany and is made of highly polished stainless steel, this also applies to the connections. Therefore, the manufacturer gives a warranty of 10 years on the reactor! With connections and reactors made of plastic, the aggressive UV radiation dissolves out plastic particles over time, the components dry out and break. What is UV water treatment? With UV or UVC irradiation, pathogenic bacteria or viruses can be inactivated. Thus they are no longer harmful to health! The treatment at a wavelength of 254nm guarantees a fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. By UV irradiation, water can be safely sterilized from germs without the use of chlorine. The process is absolutely safe and, of course, the water tastes much better than water treated with chlorine. Advantages of the UV disinfection system An additional pulse generator is installed, which measures the water flow through the system, as well as an additional board, exclusively developed for UST, which reduces the lamp power by 40%. UV lamps (low pressure lamps) are not suitable for frequent on/off switching. UV systems are therefore usually used in continuous operation, although the actual disinfection is needed only for a short time. The power of UV lamps, however, can be reduced without the lamps switching off. The PURE SE models automatically reduce lamp output by 40% if no water flows through the system for one minute. As soon as water flows again, the system is immediately back to full power. Technical information Due to the three available connections, you can choose to install from one side or the other. The connection that is not needed is closed. The disinfection capacity of 2400 l/h is achieved with a very moderate power consumption of 50 watts. Please note that the water to be treated must be at least 95% clear for this (*SSK< 95%), so a good pre-filtration is absolutely necessary! Solutions for this can be found here in our store, please contact us on this in case of need. Thank you! Maintenance Exchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then pulled out to replace. Connections: 1" inch *SSK= spectral attenuation coefficient, i.e. the water must be at least 95% transparent, otherwise pre-filtration is necessary  

The UV water treatment system Pure 2.4 120W from the manufacturer UST is used to inactivate germs such as bacteria and viruses. It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment?Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical informationDue to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of 6000 l/h is achieved with a very low power consumption of 120 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! MaintenanceExchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: Standard 2 "inch or alternatively 1" inch possible (if 1 "inch desired, please specify when ordering). * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary

The UV water treatment system Pure L + 120W from the manufacturer UST is used to inactivate germs such as bacteria and viruses. The system is designed for use in closed containers. It is completely made in Germany. What is UV water treatment? Pathogenic bacteria or viruses can be inactivated with UV or UVC irradiation. This means that they are no longer harmful to health! Treatment at a wavelength of 254 nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. With UV irradiation, germs can safely make water usable without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what has been treated with chlorine. Technical information The disinfection performance is achieved with a very low power consumption of 120 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! Maintenance Replacement of the UV lamp every 12 months or a maximum of 9000 hours. The lamp can be exchanged simply by pulling it out. Connections: For installation, a 36 mm diameter hole is required in the middle of the tank. The length of the quartz glass tube (holder for lamp) is 975 mm. * SSK = spectral attenuation coefficient, i.e. This means that the water must be at least 95% transparent, otherwise pre-filtration is necessary

The UV water treatment system PURE D 40 W for tanks up to 1000l capacity, from the German manufacturer UST. The UV system is used to inactivate germs such as bacteria, viruses or to prevent the formation of algae.  It is a very efficient, easy-to-install solution for the use of immersion lamps in storage tanks. The newly developed immersion lamp holder enables a quick and easy installation of the PURE D 40 W. To do this, a hole with a diameter of 7-10cm is drilled in the tank lid and then the immersion lamp is fixed in it with the help of the new holder, ready. This effectively disinfects the tank and the water at the tap is germ-free. As long as there is water in the tank, the lamp can be operated, but it is also suitable for combination with solar panels as a power source: If the lamp is not operated during the night hours, the water should only be drunk after 30min of irradiation. The system is completely manufactured in Germany. What is UV water treatment? With UV or UVC irradiation, pathogenic bacteria or viruses can be inactivated. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm guarantees a fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. Through UV irradiation, water can be safely cleansed of germs without the use of chlorine. The process is absolutely harmless and, of course, the water tastes much better than water treated with chlorine. Technical information The disinfection performance is achieved with a very low power consumption of 40 watts. Please note that the water to be treated must be at least 95% clear (*SSK< 95%), so good pre-filtration is absolutely essential! You can find solutions for this here in our shop, please contact us if necessary. Thank you! Maintenance Replace the UV lamp every 12 months or max. 8000 hours. The lamp can be easily replaced by pulling it out. Connections: For installation, a hole of 70-100 mm diameter is required in the center of the tank. The length of the quartz glass tube (holder for lamp) is 950 mm. *SSK= spectral attenuation coefficient, i.e. the water must be at least 95% transparent, otherwise pre-filtration is necessary.    

The UV water treatment system Pure 1.0 16W S 12 VDC from the manufacturer UST is used to inactivate germs such as bacteria and viruses. Perfectly adapted for operation on 12 volt systems! It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment? Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical information Due to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of 330 l/h is achieved with a extremely low power consumption of 16 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! Maintenance Exchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: 1/2" inch * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary

The UV water treatment system Pure 1.2 21W 24 CVD from the manufacturer UST is used to inactivate germs such as bacteria and viruses. Perfectly adapted for operation on photovoltaic systems. It is manufactured entirely in Germany and consists of highly polished stainless steel, this also applies to the connections. The manufacturer therefore gives a 10-year guarantee on the reactor! In the case of connections and reactors made of plastic, the aggressive UV radiation releases plastic particles over time, the components dry out and break. What is UV water treatment? Pathogenic bacteria or viruses can be inactivated with UV or UVC radiation. This means that they are no longer harmful to health! The treatment at a wavelength of 254nm ensures fast, effective and safe disinfection. This process is economical and has been used worldwide for many years. UV radiation enables water from germs to be used safely without the use of chlorine. The process is absolutely harmless and of course the water tastes much better than what is treated with chlorine. Technical information Due to the three existing connections, you can choose to install from one side or the other. The connection that is not required is closed. The sterilization capacity of 1080 l/h is achieved with a extremely low power consumption of 21 watts. Please note that the water to be treated must be at least 95% clear (* SSK <95%), so good pre-filtration is absolutely necessary! You can find solutions here in our shop, please contact us if necessary. Thank you! Maintenance Exchange of the UV lamp every 12 months or max 9000 hours. The lamp can be easily loosened by screws and then replaced by pulling it out. Connections: 1" inch * SSK = spectral attenuation coefficient, i.e. that is, the water must be at least 95% transparent, otherwise pre-filtration is necessary