Filteranlagen für Eisen und Mangan belastetes Wasser oder zur pH-Wert Anhebung

The assembly block is suitable for the AquaAvanti IronGo iron filter and manganese filter AquaAvanti ManganGo or where a bypass is needed. If there is limited space at the point of connection, the use of a mounting block is ideal. For safety reasons, it may be desirable to be able to bridge the device unit. For such cases, the mounting block (bypass) is ideal. The installation of a mounting block usually takes about one hour. Your installer will surely make you an offer. If you are not sure if you need a mounting block just ask him. The mounting block is working that way Position 1 When the two outer taps are closed and the middle tap is open, the water flows past the connected device (eg AquaAvanti Iron GO or AquaAvanti ManganGo). Position 2 If the two outer cocks are open and the middle closed, all the water flows through the connected devices. Note: If it is necessary to bridge the units, simply return the mounting block to position 1.

Very high quality armored hose as 1 inch version with 1 x union nut (ÜM) and 1 x union nut (ÜM). The polyethylene (PE) hose has a flat seal and is DIN-DVGW tested. The connections are nickel-plated brass. The armored hose is of course suitable for drinking water installations and also for sanitary and water softening systems. The hose material is very flexible and has a high thermal resistance. The high-quality, flexible hose was produced with a drinking water approval (KTW A, W270, W543, DVGW) and is resistant to electrical corrosion. In addition, it has a vacuum resistance of up to 0.1 mbar, even with the smallest bending gradients and temperatures of up to + 80 ° C.

With the BRUNNENWASSER PLUS water test you can quickly and easily get an overview of the water quality of your fountain. The analysis includes the main pollutants in the water. The advantages of the water test     Simple sampling including instructions - no previous knowledge required     Water analysis in the accredited water laboratory DIN-EN-ISO 17025     Express analysis of your water sample (3-7 days), including expert tips     Analysis time only about 7 working days     Easy interpretation due to traffic light function of the analysis results also understandable for laypersons     If limits are exceeded, there are brief explanations of possible original causes The wide analysis spectrum of the Brunnenwasser Plus water test examines your water samples in addition to many important test values ??for microbiological parameters such as E.coli bacteria and enterococci. These can cause infections in immunodeficient people and therefore must not be contained in your drinking water. This water test tests your well water on a total of 19 test values, so that it can be safely used that goes beyond the irrigation of ornamental and useful plants. How is the well water PLUS analysis?After placing your order, we will send the water analysis set within 24 hours by Deutsche Post / DHL or UPS courier. The test set contains everything you need for sampling, such as sampling vessels, detailed instructions and of course a free return label. You do not need to have any previous knowledge. If you have any questions, the IVARIO drinking water experts and of course we from the water filter center team are available free of charge by phone and e-mail. Which pollutants are analyzed in the Brunnenwasser PLUS water test? The Brunnenwassertest PLUS includes the analysis of the following substances, according to the detection limits of the Drinking Water Ordinance (TrinkwVO): Indicator parameters coliform germs (intestinal germs) microbiological parameters drinking water regulationE. coliEnterococci Heavy metals     lead    silver    zinc Minerals and hardness agents     iron    magnesium    manganese    calcium    sulfate    chloride    beryllium    Water hardness (total hardness) nitrogenous compounds     ammonium    nitrite    nitrate further examination parameters     PH value    electric conductivity We wish you much success and a good test result!

The set is tool-free and very easy to use during routine maintenance. We recommend to do this every 24 months. It fits all Clack WS 1 CI control heads no matter where they are used.     Scope of delivery: Main piston seal cage, main piston & bowl

Very high quality armored hose as 1 inch version with 1 x union nut (ÜM) and 1 x union nut elbow (ÜMB). The polyethylene (PE) hose has a flat seal and is DIN-DVGW tested. The connections are nickel-plated brass. The armored hose is of course suitable for drinking water installations and also for sanitary and water softening systems. The hose material is very flexible and has a high thermal resistance. The high-quality, flexible hose was produced with a drinking water approval (KTW A, W270, W543, DVGW) and is resistant to electrical corrosion. In addition, it has a vacuum resistance of up to 0.1 mbar, even with the smallest bending gradients and temperatures of up to + 80 ° C.

The iron rapid test is suitable for testing a defrosting system such as the AquaAvant IronGo or the AquaAvanti ManganGo, as well as other defrosting systems. The test we provide lasts for up to 100 tests. It does not replace well-founded water analysis from an accredited laboratory but is sufficiently well suited to check the function of a de-ironing plant.

The filter material Calzit can be used universally and is mainly used for the treatment of drinking water and industrial water. Application areas: • Filtration of spring and surface water containing turbid matter • Filtration in connection with the deacidification • Filtration of circulating water (cooling water, service water, in industry) Advantages: • Universal filter material • Iron removal and manganese removal due to its alkaline reaction and porosity • Increase in the filtration speed

The connection set is suitable for the disinfestation systems AquaAvanti IronGo (except EV-B1 and EW-B1) and equipment for manganese removal such as AquaAvanti ManganGo (except models with 3,3m³/h and 4,4m³/h flowrate) or just as it is needed. Delivery The connection set 1 inch contains: 2x armored hose DVGW 1 "ÜMxÜM, L-1.000mm, drain hose and overflow hose each 1.500mm, 1/2" hose clamp, 4 gaskets

Das GREENSANDPLUS™ Filtergranulat bestehet aus Glaukonit (komplexes Silikat) und wird zur Entfernung von Eisen, Mangan und Schwefelwasserstoff aus Wasser verwendet. Die Beschichtung aus Mangandioxid wirkt als Katalysator bei der Oxidation von gelöstem Eisen und Mangan. Der Kern aus Silikatsand ist mit einer Mangandioxidschicht verschmolzen. Der Kern macht GREENSAND PLUS™ widerstandsfähig für Aufbereitungsprozesse mit Wässern, die geringe Wasserhärten aufweisen, einen sehr kleinen Silikatgehalt haben oder einen geringen Salzgehalt aufweisen. Es zeichnet sich durch einen hohe Fließgeschwindigkeit im Filter aus, und ist für die kontinuierliche Regeneration, als auch für die diskontinuierliche Regeneration gut geeignet.   GREENSAND PLUS™ wird in der nicht regenerierten Form geliefert und muss vor Inbetriebnahme mit einer Kaliumpermanganatlösung aktiviert werden. Wir empfehlen  einen Einwirkzeit der Kaliumpermanganatlösung von mind. 12-24 Stunden. Danach wird die Kaliumpermanganatlösung ausgespült und das Filtermaterial ist einsatzbereit.

Very high quality armored hose as 1 inch version with 1 x union nut (ÜM) and 1 x union nut elbow (ÜMB). The polyethylene (PE) hose has a flat seal and is DIN-DVGW tested. The connections are nickel-plated brass. The armored hose is of course suitable for drinking water installations and also for sanitary and water softening systems. The hose material is very flexible and has a high thermal resistance. The high-quality, flexible hose was produced with a drinking water approval (KTW A, W270, W543, DVGW) and is resistant to electrical corrosion. In addition, it has a vacuum resistance of up to 0.1 mbar, even with the smallest bending gradients and temperatures of up to + 80 ° C.

Very high quality armored hose as 1 inch version with 1 x union nut (ÜM) and 1 x union nut (ÜM). The polyethylene (PE) hose has a flat seal and is DIN-DVGW tested. The connections are nickel-plated brass. The armored hose is of course suitable for drinking water installations and also for sanitary and water softening systems. The hose material is very flexible and has a high thermal resistance. The high-quality, flexible hose was produced with a drinking water approval (KTW A, W270, W543, DVGW) and is resistant to electrical corrosion. In addition, it has a vacuum resistance of up to 0.1 mbar, even with the smallest bending gradients and temperatures of up to + 80 ° C.

The WatPass ManganGo removes manganese and iron from your well water and thus reduces the orange-brown color of the water. It also reduces often occurring, unpleasant hydrogen sulfide and turbidity of the water. The system is almost maintenance free. It only needs to be refilled every 3-4 months of potassium permanganate to regenerate the catalyst granules in the additional container. Its performance* is outstanding, it can filter up to 4.8 mg / l of iron and up to 2 mg / l of manganese from the water. The installation is very easy. At free programmable time (about every 7 days), the concentrate is automatically disposed of through a spout. The system consists of a GRP pressure bottle filled with high-quality catalyst granules and a potassium permanganate reservoir (KMnO4), which is needed to regenerate the filter material. A quantity-controlled central control valve, type Clack WS 1 CI, currently represents the ultimate in the field of control valves for such systems. An additionally obtainable assembly block (bypass) serves to bridge, but is not absolutely necessary for operation, but it is recommended. Function of the special filter material The plant can filter iron, manganese and hydrogen sulfide from your well water in one go. The filter material is coated with manganese dioxide and acts as a catalyst. The manganese and iron present are oxidized by the catalyst granules and can be filtered in the then present form. The substances held in the filter bed are then removed from the device during the backwashing process. The filter granulate is supplied for technical reasons in the non-regenerated form. Therefore, it must be activated with a potassium permanganate solution during commissioning. The WatPass ManganGo is specially equipped for us with a second granulate, which also ensures that any remaining turbidity from your well water to remove. This is rarely found in the form. In order to be able to successfully filter manganese and iron, this is possible with the AA ManganGo even at a pH of at least 6.8. So in most cases, you do not have to install an additional pH enhancement device such as the WatPass phGo. Areas of application: Well water, garden irrigation, laundries, industrial water use, Koi and fish ponds and all areas where a high manganese and iron content in the water causes problems Depending on the desired performance, or the quantity of well water to be treated, the WatPass ManganGo is available in various versions. These can be found in the selection menu. Depending on the spatial conditions and equipment requirements, we recommend that you consider the purchase of the following accessories: Connection set 1 inch depending on system size 2x armored hose 1 inch ÜM x 1 inch ÜM, L = 1.000 mm; 1x drain hose, L = 2,000mm; 1x hose clamp 1/2 inch; 4x seals; 1x overflow hose, L = 2.000mm Connection set 1 1/4 inch depending on system size 2x armored hose 1 1/4 inch ÜM x 1 1/4 inch ÜM, L = 1.000 mm; 1x drain hose, L = 2,000mm; 1x hose clamp 1/2 inch; 1x overflow hose; L = 2.000mm; 4x seals Mounting block 1 inch IG x 1 inch AG with intersection, bypass function, sampling tap Installation instructions for connection to public networks: If the ManganGo filter systems are to be used in the drinking water sector, they must comply with the "Rules for drinking water installations" according to DIN 1988 -200 in conjunction with DIN EN 1717: 2011-08. Then it is necessary to install a backflow preventer to protect the public drinking water network. Necessary installation conditions: Water connection socket 230 V / 50 Hz, waste water connection, pressure reducer at> 6 bar Transport: The article is delivered to avoid transport damage by freight carrier. * The indicated filter capacities are max. achievable values ??under exactly analyzed conditions. A water analysis and determination of what the water should be used for is a basic requirement for good advice and the selection of the right filter system. Well water can be subject to variations in composition due to various environmental factors. Therefore, a regular analysis should take place to be able to adapt the filter devices by, for. B. the regeneration cycle is changed.

Die WatPass® KombiGo entfernt Mangan und Eisen aus Ihrem Brunnenwasser und gleichzeitig wird das Wasser noch enthärtet.  NEUHEIT - Steuerungskopf Clack mit deutschem Menü und Farbdisplay. Die Farbmodi des Displays machen es leichter die Betriebszustände (blau = alles in Ordnung) zu überprüfen. Sollte mal ein Fehler vorliegen (rot = Störung), sieht man dies mit einem Blick. Das deutsche Menü erleichtert die Einstellung der Anlage enorm. Weitere Menüsprachen sind EN,FR, ES und polnisch. Die Anlage ist nahezu wartungsfrei. Es muss lediglich alle 3-4 Monate Salz, zum Regenerieren des Filtermaterials, im Zusatzbehälter nachgefüllt werden.  Seine Leistung* ist herausragend, er kann bis zu 10,0 mg/l Eisen sowie 2,0 mg/l Mangan aus dem Wasser filtern. Ganz nebenbei wird das Wasser auch noch enthärtet. Die Installation der Anlage ist sehr einfach. Mengengesteuert wird die Anlage automatisch regeneriert und das Rückspülwasser durch einen Auslauf entsorgt. Die Anlage bestehend aus einer GFK- Druckflasche (Größe wird der Leistung angepasst), die mit hochwertigem Filtermaterial gefüllt ist, sowie einem Salz-Vorratsbehälter der zur Regeneration des Filtermaterials benötigt wird. Ein mengengesteuertes Zentralsteuerventil, vom Typ Clack WS 1 CI IA, stellt momentan das Nonplusultra im Bereich der Steuerventile für solche Anlagen dar. Ein zusätzlich erwerbbarer Montageblock (Bypass) dient der Überbrückung, ist aber zum Betrieb nicht unbedingt nötig, allerdings sehr empfehlenswert. Funktionsweise des speziellen Filtermaterials Die Anlage kann in einem Durchgang Eisen und  Mangan aus Ihrem Brunnenwasser filtrieren und das Wasser gleichzeitig enthärten. Das Filtermaterial ist eine Kombination aus Adsorbern und Ionenaustauscherharzen. Die im Filterbett festgehaltenen Stoffe werden dann beim Rückspülvorgang aus dem Gerät entfernt. Das gibt es in der Form selten zu finden. Um erfolgreich Mangan und Eisen filtern zu können, benötigt die WatPass KombiGo einen pH-Wert von mindestens 5,5 und max. 9,0. Normalerweise muss der pH-Wert für die FE und Mn Filtrierung deutlich höher liegen, als bei dieser innovativen Anlage. Anwendungsbereiche: Brunnenwasser, Gartenbewässerung, Wäschereien, Brauchwassernutzung, Koi-  und Fischteiche und alle Bereiche wo ein zu hoher Mangan- und Eisengehalt im Wasser Probleme verursacht Je nach Leistungswunsch, bzw. zu behandelnde Brunnenwassermenge gibt es die WatPass KombiGo in verschiedene Ausführungen (die Farbe der Druckflasche kann bei einigen Ausführungen abweichen). Diese finden Sie im Auswahlmenü. Weiter Angaben zu Maßen und technische Daten finden sie unten im Downloadbereich.   Je nach räumlichen Gegebenheiten und Ausstattungswunsch, empfehlen wir Ihnen noch über die Anschaffung des folgenden Zubehöres nachzudenken: Anschlussset 1 Zoll  je nach Anlagengröße 2x Panzerschlauch 1 Zoll ÜM x 1 Zoll ÜM, L=1.000 mm; 1x Abflussschlauch, L= 2.000mm; 1x Schlauchschelle 1/2 Zoll; 4x Dichtungen; 1x Überlaufschlauch, L= 2.000mm Anschlussset 1 1/4 Zoll je nach Anlagengröße 2x Panzerschlauch 1 1/4 Zoll ÜM x 1 1/4 Zoll ÜM, L=1.000 mm; 1x Abflussschlauch, L= 2.000mm; 1x Schlauchschelle 1/2 Zoll; 1x Überlaufschlauch; L=2.000mm; 4x Dichtungen Montageblock 1 Zoll IG x 1 Zoll AG mit Verschneidung, Bypassfunktion, Probeentnahmehahn   Installationshinweis für den Anschluss an öffentliche Netze: Wenn die KombiGo Filteranlagen im Trinkwasserbereich eingesetzt werden sollen, müssen Sie den "Regeln für Trinkwasserinstallationen" nach DIN 1988 -200 in Verbindung mit der DIN EN 1717:2011-08 entsprechen. Dann ist es erforderlich einen Rohrtrenner zum Schutz des öffentlichen Trinkwassernetzes einzubauen. Notwendige Einbaubedingungen: Wasseranschluss  Steckdose 230 V / 50 Hz, Abwasseranschluss, Druckminderer bei > 6 bar Transport und -kosten: Der Artikel wird zum Vermeiden von Transportschäden per Spedition geliefert. *Die angegebenen Filterleistungen sind max. erreichbare Werte unter genau analysierten Bedingungen. Eine Wasseranalyse und Festlegung wofür das Wasser genutzt werden soll, ist Grundvoraussetzung für eine gute Beratung und die Auswahl des richtigen Filtersystems. Brunnenwasser kann, durch verschiedene Umwelteinflüsse, Schwankungen in der Zusammensetzung unterliegen. Daher sollte eine regelmäßige Analyse stattfinden, um die Filtergeräte anpassen zu können, indem z. B. der Regenerationszyklus verändert wird.    

The connection set is suitable for the ironing machines WatPass IronGo and manganese removal systems such as WatPass ManganGo (3.3m³ / h and 4.4m³ / h) or just as it is needed. Delivery The connection set 1 1/4 inch contains: 2x armored hose DVGW 1 1/4" ÜM x 1 1/4 "ÜM, L = 1.000 mm; 1x drain hose, L = 2.000mm; 1x hose clamp 1/2"; 1x overflow hose; L = 2.000mm; 4x seals  

The WatPass® IronGo deferrisation system oxidises dissolved iron from your water. The Clack control head with German menu and colour display distinguishes this system from many other suppliers, as usually only monochrome, English-language versions are offered. The colour modes of the display make it easier to check the operating status (blue = everything is OK). If there is an error (red = fault), you can see this at a glance. The German menu makes setting the system much easier. Nothing needs to be changed or topped up. The IronGo is therefore virtually maintenance-free. Its performance is outstanding, it can filter up to 5 mg/l of iron from the water. Installation is very simple. Even during the backwash, water can be easily removed. At a freely programmable time (approximately every 7 days), the concentrate is automatically disposed of through an outlet. A 3 metre drain hose is supplied and can be replaced with a longer garden hose if necessary. An additional mounting block (accessory) can be purchased for bridging, but is not absolutely necessary for operation, although it is highly recommended. This helps to maintain the water supply with untreated water during maintenance work. The system consists of: GRP pressure bottle in various sizes (adapted to the capacity), which is filled with high-quality filter material. The catalyser granulate is coated with manganese dioxide (MnO2). Volume-controlled central control valve type Clack WS 1 CI IA. How the catalyst granulate works Iron is usually present as bicarbonate in groundwater.  Due to the excess carbonic acid, iron cannot be filtered. As a catalyser, the filter material causes the transition from soluble Fe2+ to insoluble Fe3+, the resulting oxidation product iron hydroxide is easily filterable. A pH value of at least 6.8 (preferably 7.0) is required to filter iron successfully, regardless of the filter material used. If the pH value of your water is too low, please contact us specifically. This must then be raised by additional filter technology as a first step. We then recommend the WatPass pHGO system. Necessary installation conditions: Water connection socket 230 V / 50 Hz, waste water connection, pressure reducer at > 6 bar Product Details Flexible, space-saving design Corrosion-resistant GRP pressure bottle High-quality filter material Computer-controlled Clack WS 1 CI IAValve Volume Control Extremely low maintenance Treatment of ferrous water Reduction of the orange-brown colour tone in the water Areas of application: Well water, garden irrigation, laundries, industrial water utilisation, koi and fish ponds and all areas where excessive iron content in the water causes problems The WatPass IronGo is available in different versions depending on the required performance or the amount of well water to be treated (the colour of the pressure bottle may differ in some versions). You can find these in the selection menu. Note: If the IronGo filter systems are to be used in the drinking water sector, they must comply with the ‘Rules for drinking water installations’ in accordance with DIN 1988 -200 in conjunction with DIN EN 1717:2011-08. It is then necessary to install a pipe separator to protect the public drinking water network.  

If, as a well operator, you have low pH levels in your water and you want to use it as drinking water, the WatPass® pHGo offers you an excellent opportunity to increase the ph value in order to comply with the regulations of the Drinking Water Ordinance (pH 6.5-9, 5, TrinkwVo 2001/11). The system consists of a GRP pressure bottle, which is filled with a material for pH increase. A volume-controlled central control valve, type Clack WS 1 CI, currently represents the ultimate in control valves for such systems. Background Acidic water is corrosive. As the pH drops, the proportion of free carbonic acid increases, attacking all metals except stainless steel. This leads to leaks in the water installation over time. It also pollutes your drinking water with copper, zinc or aluminum. The WatPass pHGo contains a mineral that neutralizes the excess carbonic acid and immediately increases the pH value. The mineral is a consumable and must be refilled 1-3 times a year, depending on local conditions. Installation Behind the well pump or in front of the pressure vessel, if available. To ensure proper backwash, a pressure control must be installed in front of the neutralizer or a bypass of the existing pressure switch to allow the well pump to start delivering water when the neutralizer backwash valve is opened. Recommendation: To maintain the performance and service life of the device, a sediment filter should be installed. If the iron and manganese contents of your well water are too high and you want to use the WatPass IronGo, but the pH value is too low for the proper functioning of the device, then the WatPass phGo is the solution for this case! The WatPass phGo raises the pH of your well water to a level that allows the WatPass IronGo to be used for iron removal, even if the pH of your water is below 6.8. The installation is serial, before the WatPass IronGo and is very simple. Depending on the desired performance or the amount of well water to be treated, the WatPass phGo is also available in other versions. If the model offered by us does not fit, of course we can also sell you another, suitable device. Just ask us! Applications Well water, garden irrigation, laundries, hot water, koi and fish ponds and all areas where too low ph value of your water prevents iron ironing with the IronGo. Depending on the spatial conditions and equipment requirements, we recommend that you consider the purchase of the following accessories: Connection set 1 inch depending on system size 2x armored hose 1 inch ÜM x 1 inch ÜM, L = 1.000 mm; 1x drain hose, L = 2,000mm; 1x hose clamp 1/2 inch; 4x seals; 1x overflow hose, L = 2.000mm Connection set 1 1/4 inch depending on system size 2x armored hose 1 1/4 inch ÜM x 1 1/4 inch ÜM, L = 1.000 mm; 1x drain hose, L = 2,000mm; 1x hose clamp 1/2 inch; 1x overflow hose; L = 2.000mm; 4x seals Mounting block 1 inch IG x 1 inch AG with intersection, bypass function, sampling tap   Note: A water analysis and determination of what the water should be used for is a prerequisite for good advice and the selection of the right filter system. Well water may be subject to variations in composition due to various environmental influences. Therefore, a regular analysis should take place to be able to adapt the filter devices by For example, the regeneration cycle is changed. Installation instructions for connection to public networks: If the WP ManganGo filter systems are to be used in the drinking water sector, they must comply with the "Rules for drinking water installations" according to DIN 1988 -200 in conjunction with DIN EN 1717: 2011-08. Then it is necessary to install a backflow preventer to protect the public drinking water network. Necessary installation conditions: Water connection socket 230 V / 50 Hz, waste water connection, pressure reducer at> 6 bar Transport and costs: The item is delivered to avoid transport damage by freight carrier.