WatPass® pHGo for raising the pH value of your well water

Fra 7.971,85 kr. *
Indhold: 1 Stück

Priser inkl. momseksl. fragt

Brunnenpumpenleistung:

  • WatPass® pHGo system - The WatPass® pHGo is required as a supplement to the WatPass® IronGo if, due to pH values below 6.8, deferrisation with this device is no longer possible.

    • 1588-001
    • 4250188802620
    If, as a well operator, you have low pH levels in your water and you want to use it as drinking... mere
    Produktinformation "WatPass® pHGo for raising the pH value of your well water"

    If, as a well operator, you have low pH levels in your water and you want to use it as drinking water, the WatPass® pHGo offers you an excellent opportunity to increase the ph value in order to comply with the regulations of the Drinking Water Ordinance (pH 6.5-9, 5, TrinkwVo 2001/11). The system consists of a GRP pressure bottle, which is filled with a material for pH increase. A volume-controlled central control valve, type Clack WS 1 CI, currently represents the ultimate in control valves for such systems.

    Background

    Acidic water is corrosive. As the pH drops, the proportion of free carbonic acid increases, attacking all metals except stainless steel. This leads to leaks in the water installation over time. It also pollutes your drinking water with copper, zinc or aluminum. The WatPass pHGo contains a mineral that neutralizes the excess carbonic acid and immediately increases the pH value. The mineral is a consumable and must be refilled 1-3 times a year, depending on local conditions.

    Installation

    Behind the well pump or in front of the pressure vessel, if available. To ensure proper backwash, a pressure control must be installed in front of the neutralizer or a bypass of the existing pressure switch to allow the well pump to start delivering water when the neutralizer backwash valve is opened.

    Recommendation: To maintain the performance and service life of the device, a sediment filter should be installed.


    If the iron and manganese contents of your well water are too high and you want to use the WatPass IronGo, but the pH value is too low for the proper functioning of the device, then the WatPass phGo is the solution for this case! The WatPass phGo raises the pH of your well water to a level that allows the WatPass IronGo to be used for iron removal, even if the pH of your water is below 6.8.

    The installation is serial, before the WatPass IronGo and is very simple. Depending on the desired performance or the amount of well water to be treated, the WatPass phGo is also available in other versions. If the model offered by us does not fit, of course we can also sell you another, suitable device. Just ask us!

    Applications

    Well water, garden irrigation, laundries, hot water, koi and fish ponds and all areas where too low ph value of your water prevents iron ironing with the IronGo.


    Depending on the spatial conditions and equipment requirements, we recommend that you consider the purchase of the following accessories:

    Connection set 1 inch depending on system size

    2x armored hose 1 inch ÜM x 1 inch ÜM, L = 1.000 mm; 1x drain hose, L = 2,000mm;
    1x hose clamp 1/2 inch; 4x seals; 1x overflow hose, L = 2.000mm


    Connection set 1 1/4 inch depending on system size

    2x armored hose 1 1/4 inch ÜM x 1 1/4 inch ÜM, L = 1.000 mm; 1x drain hose,
    L = 2,000mm; 1x hose clamp 1/2 inch; 1x overflow hose; L = 2.000mm; 4x seals

    Mounting block 1 inch IG x 1 inch AG

    with intersection, bypass function, sampling tap

     


    Note: A water analysis and determination of what the water should be used for is a prerequisite for good advice and the selection of the right filter system. Well water may be subject to variations in composition due to various environmental influences. Therefore, a regular analysis should take place to be able to adapt the filter devices by For example, the regeneration cycle is changed.

    Installation instructions for connection to public networks: If the WP ManganGo filter systems are to be used in the drinking water sector, they must comply with the "Rules for drinking water installations" according to DIN 1988 -200 in conjunction with DIN EN 1717: 2011-08. Then it is necessary to install a backflow preventer to protect the public drinking water network. Necessary installation conditions: Water connection socket 230 V / 50 Hz, waste water connection, pressure reducer at> 6 bar

    Transport and costs: The item is delivered to avoid transport damage by freight carrier.

    Relaterede links til "WatPass® pHGo for raising the pH value of your well water"
    Technical details "WatPass® pHGo for raising the pH value of your well water"
  • WatPass_pHGo_Datenblaetter
  • Maximum power: 3.5m³ / h Backwash flow: at least 3.0 m³ / h Diameter: 335 mm Height: 1398 mm mere
    Technical details "WatPass® pHGo for raising the pH value of your well water"

    Maximum power: 3.5m³ / h

    Backwash flow: at least 3.0 m³ / h

    Diameter: 335 mm

    Height: 1398 mm

    Læse, skrive og diskutere anmeldelser... mere
    Anmeldelser for "WatPass® pHGo for raising the pH value of your well water"
    Skriv en anmeldelse
    Anmeldelser vil blive synlig efter verifikation.
    Angiv venligst disse tegn i tekstfeltet.

    Felterne markeret med * er påkrævet.

    Jeg har læst og accepterer privatlivspolitikken.

    Set